Radio Specific Settings

Check your radio built in menus to make sure they are configured correctly.

Icom IC-7300

• CI-V USB Port Unlink from Remote
• CI-V USB Baud Rate and CI-V Address set to the same as in your Radio prefs
  
• CI-V USB Echo Back On
• CI-V Transceive OFF
• USB Serial Function CI-V
• Either turn OFF USB Keying or disable the DTR and RTS check boxes in your Radio prefs
  

Icom IC-7610

• CI-V USB Port Unlink from Remote
• CI-V USB Baud Rate and CI-V Address set to the same as Radio prefs
  
• CI-V USB Echo Back On
• CI-V Transceive OFF
• Either turn OFF USB Keying or disable the DTR and RTS check boxes in your Radio prefs

Icom IC-9700

• Menu - Set Connectors -
  • CI-V USB Port Unlink from Remote
  • CI-V USB Baud Rate and CI-V Address set to the same as in your Radio prefs
  • CI-V USB Echo Back On
  • CI-V Transceive OFF
  • Sat Mode AFC OFF (front panel)

Icom IC-705

• Menu - Set Connectors (USB Serial Port)
  • CI-V Address set to the same as in your Radio prefs, Baud rate determined by Radio prefs
    
  • CI-V USB Echo Back On (Note: radio Preset FT8 Mode - turns Echo Back OFF)
    
  • CI-V Transceive OFF
  • Port Type: Serial Port
  • Port: /tmp/dp_sym_ic_705
    
  • Either turn OFF USB Keying or disable the DTR and RTS check boxes in your Radio prefs
    
    
• Menu - Set Connectors (Bluetooth - Must be paired first)
  • CI-V Address set to the same as in your Radio prefs, Baud rate 19200
  • Port Type: Serial Port
    
  • Port: /dev/cu.ICOMBTIC-705-SPPDev
    
  • CI-V USB Echo Back On
  • CI-V Transceive OFF
  • Either turn OFF USB Keying or disable the DTR and RTS check boxes in your Radio prefs

Icom IC-R8600

(Use MacLoggerDX R8500 Driver)

• Menu - Set Connectors (Front or Rear USB depending on which one you are using)
  • CI-V USB Port Unlink from Remote
  • CI-V USB Baud Rate and CI-V Address set to the same as in your Radio prefs
  • CI-V USB Echo Back On
  • CI-V Transceive OFF

Xiegu G90, X6100

Requires the Send Icom Filter Width check box to be enabled in the Radio prefs

Baud Rate 19200

Yaesu FT-710

• CAT-1 RATE 38400bps (must be the same as in the Radio prefs)
• CAT-1 TIME OUT TIMER 10ms

Yaesu FT-857

• 19 Same baud rate as in the Radio prefs.
• 20 CAT.
  

Yaesu FT-897

• 19 Same baud rate as in the Radio prefs.
• 20 CAT.
  

Yaesu FT-991A

• 028 GPS/232 GPS
• 031 CAT RATE 38400bps (must be the same as in the Radio prefs)
• 032 CAT TOT 10ms
• 033 CAT RTS DISABLE (or enable the RTS check box in the Radio prefs)

Yaesu FTdx3000

• 37 USB.
• 38 Same baud rate as in the Radio prefs.
  

Yaesu FTdx10/101D/MP

• CAT RATE 38400bps (must be the same as in the Radio prefs)
• CAT RTS OFF (or enable the RTS check box in the Radio prefs)  
  
• PC KEYING - if using DTR or RTS disable DTR/RTS check boxes in Radio prefs.

Kenwood TS-590S

• 062 USB PORT BAUD RATE 115200 (must be the same as in the Radio prefs)
• Radio requires RTS check box enabled in the Radio prefs.

Kenwood TS-590SG

• 068 USB PORT BAUD RATE 115200 (must be the same as in the Radio prefs)
• Radio requires RTS check box enabled in the Radio prefs.

Kenwood TS-2000

• 056 COM PORT communication speed (must be the same as in the Radio prefs)
• Changes to radio baud rate require radio power cycle.
• Radio requires RTS check box enabled in the Radio prefs.